• Gyuto 245mm Honyaki C105-W1 Integral
  • Gyuto 245mm Honyaki C105-W1 Integral – detail view
  • Gyuto 245mm Honyaki C105-W1 Integral – side profile
  • Gyuto 245mm Honyaki C105-W1 Integral – handle detail
  • Gyuto 245mm Honyaki C105-W1 Integral – blade close-up
  • Gyuto 245mm Honyaki C105-W1 Integral – view 6
  • Gyuto 245mm Honyaki C105-W1 Integral – view 7
  • Gyuto 245mm Honyaki C105-W1 Integral – view 8
1 8

Gyuto 245mm Honyaki C105-W1 Integral

Gyuto 245mm Honyaki C105-W1 Integral

By Jonas Johnsson

No longer available

Jonas Johnsson

Reserve your place

We'll only email you when there's something to say. Invitations go out in signup order as new work becomes available.

One of the most beautiful pieces of work to pass through our doors this year. A gorgeous mirror polished Honyaki Gyuto 245mm with forged integral bolster. Jonas finished this one off with an incredible dyed and stabilised redwood burl handle with black truestone inlays.

The blade is forged from W1 steel, a fairly rare steel. Water quenched with a beautiful Hamon. The profile is classic Gyuto with a subtle curve and santoku tip, approximately 53mm tall and 245mm long the blade balances nicely just forward of the integral bolster. The geometry is pretty laser with a fairly aggressive distal taper and super classy Walkschliff grind. Incredibly thin behind the edge.

The handle features Jonas's tapered Rokkaku Hanmaru style handle, but boy is it stunning with the dark green hues and black and gold truestone. The combination is just beautiful!

Product Specification
  • Blade Type:
  • Edge Length: 245mm
  • Spine Heel: 3mm
  • Spine Mid: 1.44mm
  • Spine Tip (20mm before): 0.95mm
  • Blade Height: 53mm
  • Weight: 209g
  • Cutting Edge Steel:
  • Steel class: Carbon
  • HRC: 64+
  • Blade Construction:
  • Blade Finish: Mirror Polish
  • Grind:
  • Handle Construction:
  • Handle Materials: Stabilised Redwood Burl, Black Truestone
  • Handedness: Ambidextrous

Blade type

Gyuto

牛刀

The Japanese take on the Western chef's knife, and the most versatile blade in a modern kitchen. A gyuto carries a long, gently curved edge — most often 210 to 270 mm — that allows both push cuts and a rocking motion, with a pointed tip for fine work and enough height at the heel to keep knuckles clear of the board. It handles proteins, vegetables, and herbs without complaint, which is why most cooks reach for it first.

Compared with a European chef's knife, the gyuto is usually thinner, harder, and lighter, ground to a finer edge that rewards good board technique and regular honing. That same thinness is the trade-off: the edge is less forgiving of bone, frozen food, and twisting cuts, and it asks for a little more care in maintenance in exchange for its keenness.

View full knife type guide →

Cutting edge steel

W1

Plain high-carbon water-hardening tool steel

Typical HRC
62–65
Corrosion class
Carbon
Production
Conventional
Origin
United States (AISI)

W1 is the Western archetypal water-hardening tool steel: roughly 1.0 percent carbon, no meaningful alloying, designed to be quenched in plain water. In its kitchen knife form it overlaps closely with European C105 and Japanese SK3 / SK105, and it is the ancestor of much of the Sheffield clean-carbon tradition.

For the cook it lands at 63–64 HRC in a careful heat treat, sharpens at the level of a Hitachi white paper, and behaves at the apex like the cleanest Western carbon you can buy off the rack. The trade-offs are familiar: minimal edge retention compared to the alloyed carbons, a lively patina, and a heat treat that demands attention to detail because there is nothing in the chemistry to forgive a sloppy quench.

W1 has largely been superseded in production work by W2 and the modern engineered carbons, but it persists in the work of traditionalist American smiths and is occasionally found in revivalist Sheffield production. Among the makers Modern Cooking carries, Jonas Johnsson and ScheepersBuilt work in W1. As a reference steel for "what a pure carbon should feel like," it remains honest and useful.

View full steel guide →

Blade construction

Honyaki

The traditional Japanese single-steel forging technique, in which a high-carbon mono-steel blade is differentially hardened — clay is applied to the spine before quench, leaving only the edge to fully harden. The result is a hard cutting edge and a softer spine that improves toughness, plus the hamon (temper line) that defines the visual signature of the technique.

Honyaki is the high-water mark of Japanese knifemaking. The technique is unforgiving; a failed differential quench cracks the blade. Honyaki knives are almost always from a single high-purity carbon steel — Shirogami #1 is the canonical choice — and are priced and treated accordingly.

View full construction guide →

Grind

Walkschliff

A traditional Solingen grind — also called a kettle or kessel bulge grind — in which the blade is hollowed high on the side so its thickest point sits a little below the spine rather than at it. Below that bulge the steel is taken down to an extremely thin, finely convexed cutting edge, combining the rigidity of a thick upper blade with the keenness of a very thin one.

The Walkschliff is among the most demanding grinds to execute, historically reserved for the finest German knives and requiring years of a grinder's experience to do well. For the buyer it is a high-craft European alternative to the thin flat grinds of Japanese knives — strong, stable, and keen — but it is a hand-ground specialism, and a knife that carries it is priced for the skill it took to make.

View full grind guide →

Handle construction

Hidden Tang

A construction in which the tang runs into the handle but stays concealed inside it, rather than showing between two scales. A narrower tang — a full-length stick or a shorter projection — is set into a drilled or burned channel in a one-piece handle and secured with adhesive, a friction fit, or a threaded fitting drawn up against the blade. This is the traditional construction of Japanese wa-handles and many European hidden-tang knives.

The design puts the handle material in charge of the look and feel: a single piece of wood, horn, or composite — often with a ferrule or spacers at the front — is shaped into any cross-section the maker wants, from the classic octagonal and D-shaped wa profiles to fully rounded Western forms. With no steel showing along the grip, the handle can be slim and light, and is frequently made to be removed and replaced, with the balance sitting toward the blade.

View full construction guide →

Shipping & Returns

Shipping

We process orders 5 days a week (Monday - Friday) and ship from our shop in Sydney, Australia. We ship with FedEx, UPS and DHL.

We are happy to offer free international shipping on a variety of orders depending on location and order value.

Free Shipping Regions and Minimum Order Values

For Australia and New Zealand the minimum is $500AUD. For the rest of the world it is approximately €1000EUR. The discount is applied automatically when you reach the minimum cart value at checkout.

Returns

If you're not entirely happy with your purchase, you can return it within 14 days of delivery for a refund. The item must be in its original condition with all original packaging.

  • Returns are accepted for 14 days
  • The customer is responsible for return shipping costs
  • A 15% restocking fee may be applied to change-of-mind returns
  • We do not accept returns on second-hand items for change of mind

Faulty or Damaged Items

You must notify us within 5 business days of receiving your order. Photographic evidence of damage is required. Once approved, Modern Cooking will cover return shipping costs.

Product Care

Cleaning: Clean by hand with warm water. Avoid wetting the handle when possible.

Sharpening: We advise using whetstones to sharpen your knives and a honing rod or steel to maintain the burr between sharpening sessions.

Reactive Steels: Reactive steels like Aogami Super, Apex Ultra or premium reactive German and Swedish steels are susceptible to rust if not properly cared for. Keep the knife dry between uses and when storing for longer periods, wiping the blade with Tsubaki oil or another food-safe oil is a wise choice. A patina can be a beautiful personal feature on your knife and helps to stop rust forming.

Handle Care: For non-stabilised wooden handles, apply Tsubaki oil or another food-safe oil from time to time. Food-safe wax can be applied to both stabilised and non-stabilised wooden handles. Never apply hot wax or oil as you risk warping or damaging the handle.

View full details