Skip to product information
1 of 8

Gyuto 245mm Apex Ultra Forged S Ku Tasmanian Blackwood & G10 -58

Gyuto 245mm Apex Ultra Forged S Ku Tasmanian Blackwood & G10 -58

By Brook Turner


No longer available

Brook Turner

Reserve your place

We'll only email you when there's something to say. Invitations go out in signup order as new work becomes available.

This 245mm Gyuto is part of a small series of Brook Turner’s Forged S kitchen knives, built around a substantial semi-integral bolster and a performance-led interpretation of classic Japanese geometry. Forged from Apex Ultra, the blade carries a deep kurouchi finish above low, stone-finished convex bevels, giving the knife a purposeful, workshop-led character while keeping the cutting geometry clean and clearly defined.

In hand, the Forged S construction gives the knife noticeable authority through the heel and a comfortable swell of steel at the pinch point. Brook’s profile remains distinctly gyuto: a controlled edge curve that favours push and pull cutting while retaining enough radius for light rocking. The pronounced distal taper moves from more than 5mm above the heel to less than 1mm around 20mm behind the tip, creating a useful contrast between strength through the rear of the blade and finer control at the front. The low convex bevels are shaped to move cleanly through produce while encouraging practical food release.

The octagonal handle pairs Tasmanian Blackwood with a short G10 ferrule, keeping the material palette restrained and durable. The rich figure of the timber, dark kurouchi, satin bevels and exposed forged bolster come together in a knife that feels distinctly Brook Turner: robust, tactile and designed to reward serious use as much as close inspection.

Product Specification
  • Blade Type:
  • Overall Length: 400mm
  • Edge Length: 245mm
  • Spine Heel: 5.00mm
  • Spine Mid: 2.57mm
  • Spine Tip (20mm before): 1.07mm
  • Blade Height: 58.79mm
  • Weight: 293g
  • Cutting Edge Steel:
  • Steel class: Carbon
  • HRC: 66
  • Blade Construction:
  • Blade Finish: Kurouchi, Satin Polish
  • Grind:
  • Handle Construction:
  • Handle Materials: Tasmanian Blackwood, G10
  • Handedness: Ambidextrous

Blade type

Gyuto

牛刀

The gyuto is the Japanese interpretation of the western chef knife, and the most versatile blade in a modern kitchen. It carries a long edge, most often 210 to 270 mm, that runs flatter through the heel than its western counterpart before rising in a gentle, late curve to a fine point — a line that favours push- and pull-cutting while still allowing a rocking motion when the work calls for it. There is enough height at the heel to keep knuckles clear of the board, and the tip is fine enough for detail work, which is why most cooks reach for it first.

The flatter edge is the defining characteristic and the trade-off both. More of the blade lands on the board at once, which suits push cutting and gives clean, decisive contact through an ingredient, but a cook who works primarily by rocking will find less curve to work with than a western profile offers. Modern makers increasingly blur the line between the two, drawing a profile that rocks and push-cuts equally well — Birch & Bevel's Modern Gyuto profile, Antoine Kniamen's Western Gyuto, and Benjamin Kamon's own gyuto profile are all examples of that hybrid thinking.

View full knife type guide →

Cutting edge steel

Apex Ultra

Low-alloy fine-grain carbon tool steel

Typical HRC
64–68
Corrosion class
Carbon
Production
Conventional
Origin
Austria (ApexUltra project — developed by Larrin Thomas, Marco Guldimann and Tobias Hangler; FFG-funded, associated with Messerschmiede Hangler)

Apex Ultra is one of the most carefully engineered non-stainless kitchen knife steels in modern circulation — a steel designed from the ground up specifically for handmade knives, rather than borrowed from another industry. It was developed by metallurgist Larrin Thomas together with smiths Marco Guldimann and Tobias Hangler. It is a low-alloy carbon steel — roughly 1.25 percent carbon, 2.6 percent tungsten, 1.5 percent chromium and a 0.4 percent vanadium addition, with manganese and silicon kept low. That composition is tuned for high purity and a fine, evenly distributed mix of chromium-enriched iron carbides, tungsten carbides and vanadium carbides — the structure that lets it hold a very hard edge without the coarse carbides or plate martensite that sap toughness in other high-hardness carbon steels.

What this means for a cook is unusual permission. Apex Ultra carries very high toughness in the 66+ HRC range — the highest of any knife steel its developers have tested at that hardness — so you can ask a maker to grind it thin and run the heat treatment hard, and the edge will hold far longer than the carbon steels smiths usually forge, without microchipping. It forges and forge-welds much like 52100 or 1.2562, sharpens cleanly on natural and synthetic stones without needing diamond plates, and its modest chromium slows patina a little — though it is not stainless and should be cared for as a carbon steel.

Apex Ultra has become a signature steel of the European maker community, and the Modern Cooking catalogue carries an unusually deep bench of smiths working in it. Tobias Hangler himself heads that group, alongside Marco Guldimann, Benjamin Kamon, Martin Huber, Jonas Johnsson, Karol Karyś, Birch & Bevel, and MCx. It is genuinely a step forward — one of the relatively few cases where the marketing claims and the underlying metallurgical data are saying the same thing.

View full steel guide →

Blade construction

Mono Steel

A knife forged from a single piece of steel — no laminations, no clad layers. The simplest and most direct construction. The entire blade is the cutting steel, with no softer outer jacket to protect or contrast it. Most contemporary Western kitchen knives in carbon and stainless steel are mono-steel constructions, as are honyaki and most European bladesmith work.

The trade-off is straightforward: mono-steel knives are easier to forge, sharpen, and reason about, but the entire blade carries the cutting steel's properties — including its reactivity if it's a clean carbon. There is no soft jacket to protect a more brittle core from impact, so the heat treatment and geometry have to do all the work.

View full construction guide →

Grind

Compound Grind

A category covering blades ground with more than one geometry stacked into a single cross-section — typically a convex (or flat) primary bevel at the very edge, with one or more hollows ground higher up the blade face to relieve material behind it. The aim is food release and reduced wedging: the hollow opens an air gap so dense produce breaks away from the blade instead of clinging to it, while the convex steel at the edge keeps the apex strong and the knife driving through the cut.

The named variations in the Modern Cooking catalogue differ in where the hollows sit, how many there are, and whether the two faces are ground alike:

S-Grind — a convex primary bevel at the edge with a hollow ground into both faces just above it. The symmetrical "S"-shaped cross-section is the classic food-release grind: relief above the edge, strength at the edge.

C-Grind — an asymmetric S-grind. Both faces keep the convex primary bevel, but only one face carries the hollow above it. The single-sided relief biases food release to one side, and is simpler to grind and to maintain than a full S.

B-Grind — a stacked twin-hollow grind: a tight, narrow hollow immediately above the edge, with a second, broader and wider hollow above that. The staged relief gives especially strong food release across the height of the blade.

S-Hook Grind — also called a hook, harpoon, or J grind. An S-grind taken to an extreme, with the hollow placed very close to the cutting edge. The aggressive near-edge relief gives outstanding food release, at the price of being the most maintenance-sensitive of the family.

Asymmetrical-B Grind — a B-grind in which the twin-hollow structure is carried on one face while the other is ground differently (or left without the upper hollow), off-setting the edge. It combines the staged food release of a B-grind with the handed, steering character of an asymmetric grind.

In every case the gain is food release and reduced drag, and the shared cost is sharpening: as the edge is thinned over the knife's life, maintenance eventually reaches the hollowed steel, which cannot be flattened on a stone the way a convex or flat bevel can. How soon that happens depends on how deeply the hollows are cut and how close to the edge they sit — exactly what separates a gentle S-grind from an aggressive S-hook. These are high-craft geometries, prized by makers and experienced users for their cutting feel, and best appreciated by a cook who maintains their own edges.

View full grind guide →

Handle construction

Hidden Tang

A construction in which the tang runs into the handle but stays concealed inside it, rather than showing between two scales. A narrower tang — a full-length stick or a shorter projection — is set into a drilled or burned channel in a one-piece handle and secured with adhesive, a friction fit, or a threaded fitting drawn up against the blade. This is the traditional construction of Japanese wa-handles and many European hidden-tang knives.

The design puts the handle material in charge of the look and feel: a single piece of wood, horn, or composite — often with a ferrule or spacers at the front — is shaped into any cross-section the maker wants, from the classic octagonal and D-shaped wa profiles to fully rounded Western forms. With no steel showing along the grip, the handle can be slim and light, and is frequently made to be removed and replaced, with the balance sitting toward the blade.

View full construction guide →

Shipping & Returns

Shipping

We process orders Monday to Friday from our Sydney workshop. Australian orders are shipped with Australia Post and international orders with DHL Express. Shipping charges are calculated at checkout based on destination, shipment size and weight, and the carrier service available for the order.

Returns

If you're not entirely happy with your purchase, you can return it within 14 days of delivery for a refund. The item must be in its original condition with all original packaging.

  • Returns are accepted for 14 days
  • The customer is responsible for return shipping costs
  • A 15% restocking fee may be applied to change-of-mind returns
  • We do not accept returns on second-hand items for change of mind

Faulty or Damaged Items

You must notify us within 5 business days of receiving your order. Photographic evidence of damage is required. Once approved, Modern Cooking will cover return shipping costs.

Product Care

Cleaning: Clean by hand with warm water. Avoid wetting the handle when possible.

Sharpening: We advise using whetstones to sharpen your knives and a honing rod or steel to maintain the burr between sharpening sessions.

Reactive Steels: Reactive steels like Aogami Super, Apex Ultra or premium reactive German and Swedish steels are susceptible to rust if not properly cared for. Keep the knife dry between uses and when storing for longer periods, wiping the blade with Tsubaki oil or another food-safe oil is a wise choice. A patina can be a beautiful personal feature on your knife and helps to stop rust forming.

Handle Care: For non-stabilised wooden handles, apply Tsubaki oil or another food-safe oil from time to time. Food-safe wax can be applied to both stabilised and non-stabilised wooden handles. Never apply hot wax or oil as you risk warping or damaging the handle.

View full details